Bookbinding self taught
Date: 2026-01-23T00:00:00+00:00
Keywords: Bookbinding -- Handbooks; manuals; etc.

The Project Gutenberg eBook of Bookbinding self taught

This eBook is for the use of anyone anywhere in the United States and most other parts of the world at no cost and with almost no restrictions whatsoever. You may copy it, give it away or re-use it under the terms of the Project Gutenberg License included with this eBook or online at www.gutenberg.org. If you are not located in the United States, you will have to check the laws of the country where you are located before using this eBook.

Title: Bookbinding self taught

Author: Ben Davidson

Editor: E. Haldeman-Julius

Release date: January 23, 2026 [eBook #77757]

Language: English

Original publication: Girard: Haldeman-Julius Publications, 1927

Other information and formats: www.gutenberg.org/ebooks/77757

Credits: Carol Brown, Tim Miller and the Online Distributed Proofreading Team at https://www.pgdp.net

*** START OF THE PROJECT GUTENBERG EBOOK BOOKBINDING SELF TAUGHT ***

LITTLE BLUE BOOK NO. | 1192
Edited by E. Haldeman-Julius

Bookbinding
Self Taught

Ben Davidson

HALDEMAN-JULIUS PUBLICATIONS
GIRARD, KANSAS

Copyright, 1927,
Haldeman-Julius Company

PRINTED IN THE UNITED STATES OF AMERICA

CONTENTS

| Page
1. Little Blue Book Covers | 5
2. Tools and Materials | 12
3. Stitching | 15
4. Binding | 19
5. Rebinding Old Books | 28
6. Loose Leaf Scrap Books | 29
7. Lettering | 30

BOOKBINDING SELF TAUGHT

1. LITTLE BLUE BOOK COVERS

The satisfaction derived from rebinding torn covered books from my library has actuated me in preparing this Little Blue Book. I am the possessor of several hundred copies of the Little Blue Books, for which I have made a number of linen holders. To begin, therefore, with just such a simple proposition as the making of a linen cover or holder for one of the Blue Books would be a good start.

All you need is a piece of linen cloth, some thin card-board, white paste, scissors and a small brush which can be purchased at the five and ten-cent store. Also a ruler.

The Blue Book being 5 inches high and 3½ inches wide, cut two pieces of cardboard to measure 5¼ inches high and 3⅝ inches wide, thus making the card-board protrude ⅛ of an inch at the top and bottom and ⅛ of an inch on the side.

Now, measure the back of the Blue Book. As there is no uniform size, and since the backs of the Blue Books vary from ⅛ to ⅜ of an inch, allow ¼-inch for the back. If you were making a permanent cover for the Blue Book, you would have to measure its back exactly, but for a removable linen holder ¼-inch will suffice.

You are now ready to measure and cut the cloth. Be sure to measure your cloth at a right angle and leave ½-inch extra at the top and bottom and right side. In cutting the length and width of your linen, you will be guided by the following figures: Length, ½ plus 5¼ plus ½ or 6¼ inches from top to bottom; width, 2½ plus 3⅝ plus ¼ plus 3⅝ plus ½ or 10½ inches from left to right (the 2½ inches at the left is for the holder or pocket). Having cut your cloth 10½ inches by 6¼ inches, lay it down flat upon the table, and draw parallel lines ½ inch from the top and ½ inch from the bottom. Then draw perpendicular lines from the right as follows: ½-inch, 3⅝ inches, ¼-inch, and 3⅝ inches again. By drawing these parallel and perpendicular lines correctly, you will know just where to place the two (5¼ × 3⅝) cardboards. The diagram on your cloth will look something like Figure 1.

You are now ready to paste the card-boards in the spaces outlined in Figure 1. Place the cardboard on a piece of waste or newspaper; then dip your brush in a little water before applying the paste so as to get an even moisture; and give the cardboard a smooth coating of paste. In doing this paste work properly, it is good to have a supply of waste or newspaper at hand; also, a rough towel and a wastebasket. Having applied a smooth coating of paste to the cardboard, place it within the lines of the right frame (see Figure 1) and rub the surface of the cardboard with a clean piece of cloth; until you feel sure that it has been properly pasted. Do the same with the remaining cardboard and place it in the adjoining frame (see Figure 1).

Figure 1

Fold and crease the 2½ inches of cloth at your left, so that it will lay flat upon the left cardboard. At the top and bottom ends of this crease, and within the ½-inch of the overlapping margins of each end, cut out a piece of cloth in the shape of a V (see Figure 2). Also, at the top and bottom end of the 2½ inches of cloth, and within the ½-inch margins of both these ends, cut out two more pieces of cloth in the shape of V (see Figure 2).

Figure 2

As the cloth pocket-folder at your left is lying flat upon the left cardboard, fold both ends of the ½-inch margins of the pocket-folder inside, so that the margins will rest between the left cardboard and the pocket cloth. Take a piece of white paper 5⅛ × 2¼ and insert ¾-inch of the left side in the pocket-folder, so that ¾-inch at the top and bottom of the left sheet will rest right into the folded crease on the inside of the pocket-folder. Paste the back of the right side of the sheet on the left cardboard and the ¼-inch back of the book; there will still be left ¼-inch which can be pasted on the adjoining right cardboard. Now, paste the ½-inch margins at the top and bottom of the pocket holder, and fold them over so that they will rest outside the pocket (see Figure 3). Paste the remaining ½-inch margins at the top, bottom and right (one at a time) and turn them in; first, the top margin, then the margin at the bottom, the margin at the right being last. It will be necessary to cut out a small bit of cloth at the top and bottom of the right margin corners. As two margins meet each other at the corner of a book—each margin being ¼-inch wide—you find a corner margin ½-inch square that is not needed, and can be cut out; but, by a little practice, the corner can be so manipulated, as to make two right-angled triangles and by cutting the triangle facing toward you, make a more finished corner.

The margins being properly pasted inside the covers, take a sheet of paper (white) 5 × 3½ and paste over the right cardboard and part of the pasted margins, leaving ⅛-inch from the top, bottom and right side. This finishes your linen book holder and you can now insert the left cover of your Blue Book into the pocket of the linen holder.

Figure 3

2. TOOLS AND MATERIALS FOR BOOKBINDING

- Sewing Bench
- Flat Press
- Steel-faced Backing Boards
- Hammer
- Scissors
- Folder (bone)
- Hack Saw
- Glue Pot
- Brushes, Paste
- Ruler
- Cutter
- Cloth

The Sewing Bench is a wooden frame, consisting of four attached pieces of wood—1 flat piece 18 inches long by 8 inches wide; two upright pieces of wood, each piece being 1 foot long and an inch square. These two pieces of wood are attached at the left and right front ends of the flat piece perpendicularly, so that the two pieces are parallel to each other. Another piece of wood 18 inches long and 1 inch square connects the two uprights, and you have a sewing bench (see Figure 4).

Figure 4—Sewing Bench with 3 cords attached.

A small wooden press, which is used to give the book or its number of parts a good squeeze before the binding, can be made of two flat pieces of strong wood and made to come as close together with the aid of a metal vise. (The press can also be purchased for about $3.75.)

The steel-faced backing boards are used after the book is finished; the book being placed between the two boards with the protruding pieces of brass resting in the creases of the book. This can also be done with the aid of a metal vise. The steel-faced backing boards are made up of two pieces of strong wood 18 inches long and 12 inches wide and about 1 inch thick. At one of the long ends of each of these boards a piece of steel or brass is so attached as to protrude about ⅛ of an inch. These boards can also be purchased at a nominal cost at any business house dealing in Bookbinders’ Supplies.

The other tools, such as paste, hammer, brush, scissors, etc., can be purchased at any hardware or five and ten-cent store.

3. STITCHING

For the beginner who wishes to learn book binding in all its parts, it is advisable to take apart some old inexpensive book or magazine. In doing so, he will observe how the numerous pages are joined together by parts or “signatures” and then stitched. In taking an old book apart, one can’t help noticing how the covers were attached and how the back of the book was glued.

The average book, containing several hundred pages, is divided into a certain number of parts or sections. A section is made up of 8 pages or 16 sides. A book of 320 sides consists of 160 pages or 20 sections.

In preparing to stitch the sections of a book together, be sure to have each section in its proper place, before placing it on the sewing bench. Mark the first page of each section 1, 2, 3, etc. In order to insure a uniform width of all the sections, place them into the wooden press, so that the back of each section will be properly squeezed. Now, have all the backs protrude ¼-inch out of the press; and with a plain hack saw, make the holes as follows: ½-inch across from each end of the section, across the center, and two times across, between the center and each end-hole. (The last two being half way between the center and end-holes.) These holes are made for the cotton or stitching cord to pass through. Be careful in cutting, so as not to make the holes too deep. Cut as deep as the teeth of the saw.

Three cords are attached to the bar of the sewing bench. These cords are fastened to the base. As a section of the book is placed upon the sewing bench, the center hole and the ones to the left and the right of the center, are placed in front of these cords, so that the three cords will cover the three holes. Thread your needle, and begin stitching from the outside of the end-hole at your right; and, as the cotton is drawn inside and outside of the section, it will entwine the three cords. As you finish stitching one section, run your needle around the stitch underneath it and make a knot. These knots hold all the sections together.

After all the sections are properly stitched, cut the three cords, leaving an inch or so from each end. These extra pieces of cord are threaded and later used as part of the attachment of the book to the covers (see Figure 5).

When all the sections are stitched and properly knotted, the book is ready to be bound. End-sheets are then cut to measure the length and width of the book to be bound.

Figure 5—Showing the inside stitch of a section

4. BINDING

Suppose the book to be bound is 8 inches long, 5 inches wide and 1 inch thick. The end-sheet can be cut 8 × 10 and folded in half. Usually, two such sheets are cut, and pasted over each other. The top sheet being re-enforced by a strip of white linen 8 × 1½, leaving ¾ of an inch on each side of the crease. The end-sheets are then pasted with a half inch margin of paste, and placed over the first and last sheet of the book.

The back of the book is now ready to be glued; it is placed between two cardboards, and then placed between two contracting boards, leaving the back of the book protruding enough to be glued freely. The glue, being properly prepared, is applied to the back of the book with a stiff brush. The headbands or trimmings are then cut 1⅛ inches and placed on each end of the back. These headbands are more of an ornament, and most books today are bound without them.

The book being 8 inches long and one inch thick, cut a piece of cheese cloth 8 inches long and 4 inches wide, and place over the glued back so that 1½ inches of the cloth will lap over each side of the book. A strip of heavy paper 8 × 1 inches is cut and placed over the glued cheese cloth back. Leave the book in this position for a while to dry.

The next step is the cutting of cloth and cardboards for the cover. The book being 8 inches long and 5 inches wide, the cardboards should be cut 8¼ inches long and 4⅝ inches wide. (In making a flat back the width of the cardboards would be 5⅛.) By cutting the cardboards 8¼ inches long, you allow ⅛ inch to protrude at the top and the bottom; and by cutting the cardboards 4⅝ inches wide, you allow a space of ¼ inch adjacent to each side of the back of the book for the crease, and ⅛ of an inch margin wider than the book.

To give the book—8 inches long, 5 inches wide and 1 inch thick—a whole cloth binding it is necessary to measure the cloth as follows: length, ½ plus 8 and ¼ plus ½ (the half inches for margins at each end, and the 8¼ inches for the cardboards) making the length of your cloth 9¼ inches. In measuring the width of the book, allow space for the back, covers, creases and margins. The width, therefore, would be measured as follows: ½ plus 4⅝ plus ¼ plus 1 plus ¼ plus 4⅝ plus ½, making the total width 12¼ inches (see Figure 6). We now have the following measurements for the whole cloth covering of the book: Full length of cloth 9¼ inches. Full width of cloth 12¼ inches.

Figure 6

- aa—Card-boards 8¼ × 4⅝
- bb—Space for creases ¼ inch wide
- c—Space for 1-inch back
- dd—½-inch margins at the top and bottom
- ee—½-inch margins at the left and right

A piece of heavy paper 8¼ × 1 inch should be pasted over the 1-inch back to reinforce it. Paste the top margin and turn in; then the bottom margin. Now you have four corners to adjust before turning in the side margins. At each corner, you have a piece of cloth a half inch square, facing you, a part of which is unnecessary. With the aid of your thumb, manipulate the half inch square of cloth in such a way as to make two right-angle triangles; and cut the triangle facing you. Repeat the same process with the three remaining corners; and then turn in your left and right half inch margins. This completes your cover.

If you wish to put any letters, designs or title on your cover, now would be the proper time—for beginners. The subject of lettering will be taken up in another chapter.

To cover the same book with two different materials, such as cloth and paper or leather and cloth, it is customary to have the back and the corners of the book bound in the same material. Given the dimensions of any book, the rule is the same, in so far as allowing so much for the margin, ¼ inch for the crease on each side adjoining the back of the book.

In binding a book 9¼ inches long, 6¼ inches wide and 1½ inches thick with a buckram back and corners and linen or paper sides, measure and cut the buckram as follows: 1½ back, ¼ plus ¼ for the creases on each side, and 1½ plus 1½ inches buckram extra on each side of the cover. The total width being 5 inches. The length would be 9¼ and ½ plus ½ or 10¼ inches. The four buckram corners should be cut in four right angle triangles.

If each corner of the cover is to have a 2½-inch right angle triangle in buckram, cut two pieces of buckram 3½ inches square; which allows for a ½-inch margin—all around—to turn in. Cut both the squares along the opposite points or the hypotenuse and you have your four right-angle triangles (see Figure 7).

Figure 7—Pattern for the four corners. Dotted lines represent the margins.

The paper or cloth used to cover the rest of the book should be measured and cut as follows: length 9¼ inches and ½ plus ½ or 10¼ inches. The width will be 5¼ inches. About 2¾ inches will have to be cut away from the side covers to make place for the buckram corners. To do this work properly, bind your book first with the buckram back and corners; and then apply the side coverings (see Figure 8).

Figure 8—Outside cover of a book bound in two materials. Buckram for back and corners; cloth or paper for the sides.

Having attached the cardboards to the buckram back and corners, take the cloth or paper to be used for the side covering, and place one end (lengthwise) parallel with the buckram; allowing the cloth to lay on a ¼-inch margin of the buckram. Take a “bone” or letter opener and run the end along the cloth, so that the slant of the buckram corners will leave its impression upon the cloth or paper that you are using. Do the same with the other side. You now have four slant impressions on your cloth; and by cutting your piece of cloth ¼ inch away from the slants, but parallel to it, you will have an exact covering.

5. REBINDING OLD BOOKS

Some books only need new covers—the binding being strong. In removing the old covers, care should be taken not to cut any of the knots or stitches; otherwise the book will come apart. Also, in removing the back which usually contains the title, you may wish to repaste the title to the new covering. If the pages of the book are loose and merit restitching, remove the dry glue from the back of the book. The use of a pen knife, sand paper and a wet sponge will be necessary to remove the glue properly. The glue being properly removed from the back of the book, the sections will come apart readily. Remove the old stitchings from each section; and also examine the back of each part. If it is torn or worn out, re-enforce it with a thin slip of strong tissue paper one inch wide; so that ½ inch will rest on each side of the crease. The length of the tissue paper will depend, of course, upon the length of the page being repaired. Having taken the sections apart, you now proceed in the same manner as described in the chapter on Stitching.

6. LOOSE LEAF SCRAP BOOKS

The covers for a loose leaf scrap book can be made without a back. Measure and cut the cardboard ⅛ of an inch larger on all sides than the pages. Also, leave a ½-inch cloth margin on all sides. After the covers are finished, cut holes in their proper places—usually two at the back of each cover. Holes are cut in the pages to correspond with the holes in the cover. Two rings are run through the covers and pages; and your scrap or note-book is finished (see Figure 9). A hole puncher and rings can be had at a hardware store or at the “five and ten.”

Figure 9

7. LETTERING

Bookbinders’ ink can be purchased in small tin tubes. They come in all colors; but the dark colors are best for the beginner. The light colors—especially white—do not leave a clear impression upon the cloth. To do this work properly, it is necessary to have a tool-press, a small supply of printer’s type, and a small roller. The tool-press is a metal device to hold the type fast; and is made of a brass oblong frame with two screws. The frame is movable, and the screws are used to widen or narrow it according to the title of the book.

Suppose the title to be printed upon the back of the book is PILGRIM’S PROGRESS; and the back of the book is one inch wide. You will have to print PILGRIM’S PROGRESS on two lines—each line being less than an inch. The type used would be about the same size as the capital letters of a typewriting machine.

Place the letters “PILGRIM’S” in the tool-press. Hold the tool-press with its back facing you, and set the type from left to right. Open your tube of printers’ ink and squeeze a small bit on a piece of glass. Place the small roller over the ink; and keep on rolling back and forth until you have a smooth thin layer of ink on your roller. Apply the roller to the title once or twice, and, holding the handle of the tool-press tightly, press the letters upon the back of the book. Increase the pressure for a few seconds, and remove the tool-press. In order to ensure the title being placed properly, draw a light horizontal line on the back of the book, and place the type right under it.

Having printed the word “PILGRIM’S” on the back of your book, remove the type from your tool-press, and set up PROGRESS in the same way—repeating the same process. The word PROGRESS should be printed about ¾ of an inch below PILGRIM’S.

Before impressing the title upon the book, the beginner is advised to try it first on a piece of waste cloth or heavy paper. Only after you have made a clear and good impression upon the scrap of cloth, should you do the book.

After this is done, leave the printed title to dry and then attach the cover to the book in the manner described under “Binding.” Also, remove the surplus ink from the type, roller and glass. Use a little kerosene oil on a tooth brush for the cleaning of the type; and some cotton waste for the roller and glass. Apply a little kerosene to the cotton waste, and apply it to the roller, until all the ink is removed. Do the same for the glass.

To use dark colors such as black, blue or brown, it is necessary to employ a light cloth; or print the title on a white cloth and paste the white over the dark cloth. White ink on a dark cloth tends to blur; and Bookbinders use instead a chemical called praeger leaf. It looks like a sheet of paper with a coating of white chalk on one side. Apply several drops from the white of an egg (size) on the cloth. Place a small strip of praeger leaf over it. Heat the type to be used for several minutes (place in oven) and then apply it on the praeger leaf. The heat of the type melts the impression upon the cloth, and the “size” (white of an egg) makes it stick. Gold lettering with the use of gold leaf is done the same way.

Here too it is advisable to experiment on pieces of scrap cloth several times, and remember, “If at first you don’t succeed, try, try again.”

Transcriber’s Note:

One misspelled word was corrected, one extraneous hyphen was removed, and one unprinted letter was added.

*** END OF THE PROJECT GUTENBERG EBOOK BOOKBINDING SELF TAUGHT ***

Updated editions will replace the previous one—the old editions will be renamed.

Creating the works from print editions not protected by U.S. copyright law means that no one owns a United States copyright in these works, so the Foundation (and you!) can copy and distribute it in the United States without permission and without paying copyright royalties. Special rules, set forth in the General Terms of Use part of this license, apply to copying and distributing Project Gutenberg™ electronic works to protect the PROJECT GUTENBERG™ concept and trademark. Project Gutenberg is a registered trademark, and may not be used if you charge for an eBook, except by following the terms of the trademark license, including paying royalties for use of the Project Gutenberg trademark. If you do not charge anything for copies of this eBook, complying with the trademark license is very easy. You may use this eBook for nearly any purpose such as creation of derivative works, reports, performances and research. Project Gutenberg eBooks may be modified and printed and given away—you may do practically ANYTHING in the United States with eBooks not protected by U.S. copyright law. Redistribution is subject to the trademark license, especially commercial redistribution.

START: FULL LICENSE

THE FULL PROJECT GUTENBERG™ LICENSE

PLEASE READ THIS BEFORE YOU DISTRIBUTE OR USE THIS WORK

To protect the Project Gutenberg™ mission of promoting the free distribution of electronic works, by using or distributing this work (or any other work associated in any way with the phrase “Project Gutenberg”), you agree to comply with all the terms of the Full Project Gutenberg License available with this file or online at www.gutenberg.org/license.

Section 1. General Terms of Use and Redistributing Project Gutenberg electronic works

1.A. By reading or using any part of this Project Gutenberg electronic work, you indicate that you have read, understand, agree to and accept all the terms of this license and intellectual property (trademark/copyright) agreement. If you do not agree to abide by all the terms of this agreement, you must cease using and return or destroy all copies of Project Gutenberg electronic works in your possession. If you paid a fee for obtaining a copy of or access to a Project Gutenberg electronic work and you do not agree to be bound by the terms of this agreement, you may obtain a refund from the person or entity to whom you paid the fee as set forth in paragraph 1.E.8.

1.B. “Project Gutenberg” is a registered trademark. It may only be used on or associated in any way with an electronic work by people who agree to be bound by the terms of this agreement. There are a few things that you can do with most Project Gutenberg electronic works even without complying with the full terms of this agreement. See paragraph 1.C below. There are a lot of things you can do with Project Gutenberg electronic works if you follow the terms of this agreement and help preserve free future access to Project Gutenberg electronic works. See paragraph 1.E below.

1.C. The Project Gutenberg Literary Archive Foundation (“the Foundation” or PGLAF), owns a compilation copyright in the collection of Project Gutenberg electronic works. Nearly all the individual works in the collection are in the public domain in the United States. If an individual work is unprotected by copyright law in the United States and you are located in the United States, we do not claim a right to prevent you from copying, distributing, performing, displaying or creating derivative works based on the work as long as all references to Project Gutenberg are removed. Of course, we hope that you will support the Project Gutenberg mission of promoting free access to electronic works by freely sharing Project Gutenberg works in compliance with the terms of this agreement for keeping the Project Gutenberg name associated with the work. You can easily comply with the terms of this agreement by keeping this work in the same format with its attached full Project Gutenberg License when you share it without charge with others.

1.D. The copyright laws of the place where you are located also govern what you can do with this work. Copyright laws in most countries are in a constant state of change. If you are outside the United States, check the laws of your country in addition to the terms of this agreement before downloading, copying, displaying, performing, distributing or creating derivative works based on this work or any other Project Gutenberg work. The Foundation makes no representations concerning the copyright status of any work in any country other than the United States.

1.E. Unless you have removed all references to Project Gutenberg:

1.E.1. The following sentence, with active links to, or other immediate access to, the full Project Gutenberg License must appear prominently whenever any copy of a Project Gutenberg work (any work on which the phrase “Project Gutenberg” appears, or with which the phrase “Project Gutenberg” is associated) is accessed, displayed, performed, viewed, copied or distributed:

This eBook is for the use of anyone anywhere in the United States and most other parts of the world at no cost and with almost no restrictions whatsoever. You may copy it, give it away or re-use it under the terms of the Project Gutenberg™ License included with this eBook or online at www.gutenberg.org. If you are not located in the United States, you will have to check the laws of the country where you are located before using this eBook.

1.E.2. If an individual Project Gutenberg electronic work is derived from texts not protected by U.S. copyright law (does not contain a notice indicating that it is posted with permission of the copyright holder), the work can be copied and distributed to anyone in the United States without paying any fees or charges. If you are redistributing or providing access to a work with the phrase “Project Gutenberg” associated with or appearing on the work, you must comply either with the requirements of paragraphs 1.E.1 through 1.E.7 or obtain permission for the use of the work and the Project Gutenberg trademark as set forth in paragraphs 1.E.8 or 1.E.9.

1.E.3. If an individual Project Gutenberg electronic work is posted with the permission of the copyright holder, your use and distribution must comply with both paragraphs 1.E.1 through 1.E.7 and any additional terms imposed by the copyright holder. Additional terms will be linked to the Project Gutenberg License for all works posted with the permission of the copyright holder found at the beginning of this work.

1.E.4. Do not unlink or detach or remove the full Project Gutenberg License terms from this work, or any files containing a part of this work or any other work associated with Project Gutenberg.

1.E.5. Do not copy, display, perform, distribute or redistribute this electronic work, or any part of this electronic work, without prominently displaying the sentence set forth in paragraph 1.E.1 with active links or immediate access to the full terms of the Project Gutenberg License.

1.E.6. You may convert to and distribute this work in any binary, compressed, marked up, nonproprietary or proprietary form, including any word processing or hypertext form. However, if you provide access to or distribute copies of a Project Gutenberg work in a format other than “Plain Vanilla ASCII” or other format used in the official version posted on the official Project Gutenberg website (www.gutenberg.org), you must, at no additional cost, fee or expense to the user, provide a copy, a means of exporting a copy, or a means of obtaining a copy upon request, of the work in its original “Plain Vanilla ASCII” or other form. Any alternate format must include the full Project Gutenberg License as specified in paragraph 1.E.1.

1.E.7. Do not charge a fee for access to, viewing, displaying, performing, copying or distributing any Project Gutenberg works unless you comply with paragraph 1.E.8 or 1.E.9.

1.E.8. You may charge a reasonable fee for copies of or providing access to or distributing Project Gutenberg electronic works provided that:

- • You pay a royalty fee of 20% of the gross profits you derive from the use of Project Gutenberg works calculated using the method you already use to calculate your applicable taxes. The fee is owed to the owner of the Project Gutenberg trademark, but he has agreed to donate royalties under this paragraph to the Project Gutenberg Literary Archive Foundation. Royalty payments must be paid within 60 days following each date on which you prepare (or are legally required to prepare) your periodic tax returns. Royalty payments should be clearly marked as such and sent to the Project Gutenberg Literary Archive Foundation at the address specified in Section 4, “Information about donations to the Project Gutenberg Literary Archive Foundation.”

- • You provide a full refund of any money paid by a user who notifies you in writing (or by e-mail) within 30 days of receipt that s/he does not agree to the terms of the full Project Gutenberg™ License. You must require such a user to return or destroy all copies of the works possessed in a physical medium and discontinue all use of and all access to other copies of Project Gutenberg™ works.

- • You provide, in accordance with paragraph 1.F.3, a full refund of any money paid for a work or a replacement copy, if a defect in the electronic work is discovered and reported to you within 90 days of receipt of the work.

- • You comply with all other terms of this agreement for free distribution of Project Gutenberg™ works.

1.E.9. If you wish to charge a fee or distribute a Project Gutenberg™ electronic work or group of works on different terms than are set forth in this agreement, you must obtain permission in writing from the Project Gutenberg Literary Archive Foundation, the manager of the Project Gutenberg™ trademark. Contact the Foundation as set forth in Section 3 below.

1.F.

1.F.1. Project Gutenberg volunteers and employees expend considerable effort to identify, do copyright research on, transcribe and proofread works not protected by U.S. copyright law in creating the Project Gutenberg™ collection. Despite these efforts, Project Gutenberg™ electronic works, and the medium on which they may be stored, may contain “Defects,” such as, but not limited to, incomplete, inaccurate or corrupt data, transcription errors, a copyright or other intellectual property infringement, a defective or damaged disk or other medium, a computer virus, or computer codes that damage or cannot be read by your equipment.

1.F.2. LIMITED WARRANTY, DISCLAIMER OF DAMAGES - Except for the “Right of Replacement or Refund” described in paragraph 1.F.3, the Project Gutenberg Literary Archive Foundation, the owner of the Project Gutenberg™ trademark, and any other party distributing a Project Gutenberg™ electronic work under this agreement, disclaim all liability to you for damages, costs and expenses, including legal fees. YOU AGREE THAT YOU HAVE NO REMEDIES FOR NEGLIGENCE, STRICT LIABILITY, BREACH OF WARRANTY OR BREACH OF CONTRACT EXCEPT THOSE PROVIDED IN PARAGRAPH 1.F.3. YOU AGREE THAT THE FOUNDATION, THE TRADEMARK OWNER, AND ANY DISTRIBUTOR UNDER THIS AGREEMENT WILL NOT BE LIABLE TO YOU FOR ACTUAL, DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE OR INCIDENTAL DAMAGES EVEN IF YOU GIVE NOTICE OF THE POSSIBILITY OF SUCH DAMAGE.

1.F.3. LIMITED RIGHT OF REPLACEMENT OR REFUND - If you discover a defect in this electronic work within 90 days of receiving it, you can receive a refund of the money (if any) you paid for it by sending a written explanation to the person you received the work from. If you received the work on a physical medium, you must return the medium with your written explanation. The person or entity that provided you with the defective work may elect to provide a replacement copy in lieu of a refund. If you received the work electronically, the person or entity providing it to you may choose to give you a second opportunity to receive the work electronically in lieu of a refund. If the second copy is also defective, you may demand a refund in writing without further opportunities to fix the problem.

1.F.4. Except for the limited right of replacement or refund set forth in paragraph 1.F.3, this work is provided to you ‘AS-IS’, WITH NO OTHER WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PURPOSE.

1.F.5. Some states do not allow disclaimers of certain implied warranties or the exclusion or limitation of certain types of damages. If any disclaimer or limitation set forth in this agreement violates the law of the state applicable to this agreement, the agreement shall be interpreted to make the maximum disclaimer or limitation permitted by the applicable state law. The invalidity or unenforceability of any provision of this agreement shall not void the remaining provisions.

1.F.6. INDEMNITY - You agree to indemnify and hold the Foundation, the trademark owner, any agent or employee of the Foundation, anyone providing copies of Project Gutenberg™ electronic works in accordance with this agreement, and any volunteers associated with the production, promotion and distribution of Project Gutenberg™ electronic works, harmless from all liability, costs and expenses, including legal fees, that arise directly or indirectly from any of the following which you do or cause to occur: (a) distribution of this or any Project Gutenberg work, (b) alteration, modification, or additions or deletions to any Project Gutenberg work, and (c) any Defect you cause.

Section 2. Information about the Mission of Project Gutenberg

Project Gutenberg is synonymous with the free distribution of electronic works in formats readable by the widest variety of computers including obsolete, old, middle-aged and new computers. It exists because of the efforts of hundreds of volunteers and donations from people in all walks of life.

Volunteers and financial support to provide volunteers with the assistance they need are critical to reaching Project Gutenberg’s goals and ensuring that the Project Gutenberg collection will remain freely available for generations to come. In 2001, the Project Gutenberg Literary Archive Foundation was created to provide a secure and permanent future for Project Gutenberg and future generations. To learn more about the Project Gutenberg Literary Archive Foundation and how your efforts and donations can help, see Sections 3 and 4 and the Foundation information page at www.gutenberg.org.

Section 3. Information about the Project Gutenberg Literary Archive Foundation

The Project Gutenberg Literary Archive Foundation is a non-profit 501(c)(3) educational corporation organized under the laws of the state of Mississippi and granted tax exempt status by the Internal Revenue Service. The Foundation’s EIN or federal tax identification number is 64-6221541. Contributions to the Project Gutenberg Literary Archive Foundation are tax deductible to the full extent permitted by U.S. federal laws and your state’s laws.

The Foundation’s business office is located at 41 Watchung Plaza #516, Montclair NJ 07042, USA, +1 (862) 621-9288. Email contact links and up to date contact information can be found at the Foundation’s website and official page at www.gutenberg.org/contact

Section 4. Information about Donations to the Project Gutenberg Literary Archive Foundation

Project Gutenberg™ depends upon and cannot survive without widespread public support and donations to carry out its mission of increasing the number of public domain and licensed works that can be freely distributed in machine-readable form accessible by the widest array of equipment including outdated equipment. Many small donations ($1 to $5,000) are particularly important to maintaining tax exempt status with the IRS.

The Foundation is committed to complying with the laws regulating charities and charitable donations in all 50 states of the United States. Compliance requirements are not uniform and it takes a considerable effort, much paperwork and many fees to meet and keep up with these requirements. We do not solicit donations in locations where we have not received written confirmation of compliance. To SEND DONATIONS or determine the status of compliance for any particular state visit www.gutenberg.org/donate.

While we cannot and do not solicit contributions from states where we have not met the solicitation requirements, we know of no prohibition against accepting unsolicited donations from donors in such states who approach us with offers to donate.

International donations are gratefully accepted, but we cannot make any statements concerning tax treatment of donations received from outside the United States. U.S. laws alone swamp our small staff.

Please check the Project Gutenberg web pages for current donation methods and addresses. Donations are accepted in a number of other ways including checks, online payments and credit card donations. To donate, please visit: www.gutenberg.org/donate.

Section 5. General Information About Project Gutenberg electronic works

Professor Michael S. Hart was the originator of the Project Gutenberg concept of a library of electronic works that could be freely shared with anyone. For forty years, he produced and distributed Project Gutenberg eBooks with only a loose network of volunteer support.

Project Gutenberg eBooks are often created from several printed editions, all of which are confirmed as not protected by copyright in the U.S. unless a copyright notice is included. Thus, we do not necessarily keep eBooks in compliance with any particular paper edition.

Most people start at our website which has the main PG search facility: www.gutenberg.org.

This website includes information about Project Gutenberg, including how to make donations to the Project Gutenberg Literary Archive Foundation, how to help produce our new eBooks, and how to subscribe to our email newsletter to hear about new eBooks.

Table of Contents

- Bookbinding Self Taught

- CONTENTS

- BOOKBINDING SELF TAUGHT

- 1. LITTLE BLUE BOOK COVERS
- 2. TOOLS AND MATERIALS FOR BOOKBINDING
- 3. STITCHING
- 4. BINDING
- 5. REBINDING OLD BOOKS
- 6. LOOSE LEAF SCRAP BOOKS

- 7. LETTERING

- Transcriber’s Note:

- THE FULL PROJECT GUTENBERG™ LICENSE